Installation Instructions for the OWLET IV NEMA
OWLET IV
NEMA Luminaire Controllers
Installation Instructions
DATALIFT N MESHNODE N
QR code to access the online
installation instruction.
IP 66
IK 08
INSTALLATION VIDEO
www.schreder.com
/4
DOC-0020638 OWLET IV NEMA-INS-B | 10-2022
OWLET IV
NEMA Luminaire Controllers
Installation Instructions
DATALIFT N MESHNODE N
QR code to access the online
installation instruction.
IP 66
IK 08
PRODUCT
DATALIFT N
MESHNODE N
Ta: -40°C to +65°C -40°F to +149°F Mains voltage: 110-240V Frequency: 50/60Hz Max load current: 5A
Ta: -40°C to +65°C -40°F to +149°F Mains voltage: 110-240V Frequency: 50/60Hz Max load current: 5A
72.9mm 2.87in
90.7mm 3.57in
Ø 92.2mm 3.63in
Ø 92.2mm 3.63in
XX/XX FW: X.X.X.X SN: XXXXXXXXXXXXXXXX
XX/XX FW: X.X.X.X SN: XXXXXXXXXXXXXXXX
0.18kg 0.40lb
0.23kg 0.51lb
kg lb
kg lb
Red bottom
Grey bottom
BEST LOCATION, RATIO & DISTANCE
1 DATALIFT : 10 MESH
DATALIFT
MAX. 500M
MAX. 100M
MESHNODES
www.schreder.com /4
1
DOC-0020638 OWLET IV NEMA-INS-B | 10-2022
INSTALLATION
Before installation contact Schréder FAE (Field Application Engineer) for support.
During installation, ensure correct body position over the luminaire.
2
1
Q
A
FAE
Turning indications on top of controller.
Controller
3
Hold controller.
NEMA Socket
Align the longer pin (Neutral) first.
4
Align the controller power pins with slots in the socket.
Check if the surfaces between the controller and NEMA socket are parallel and plug in.
Push the controller firmly down. Make sure it is vertically aligned.
5
6
± 55 N (12.5 lbf)
1
2
Correct position: vertical
Incorrect position: twisted
//
//
www.schreder.com /4 2
DOC-0020638 OWLET IV NEMA-INS-B | 10-2022
INSTALLATION
7
Turn controller ± 45° clockwise until it locks.
4.5 N.m (3.3 lbf.ft)
The installer is responsible for verifying the installation.
VERIFICATION
8
Visual Verification
Symbol on controller and gasket are aligned. NEMA socket with internal RFID
Incorrect installation: Surfaces of controller and NEMA socket are twisted.
Correct installation: Surfaces of controller and NEMA socket are parallel.
Mechanical Verification
NEMA socket with external RFID Symbol on controller and socket label are aligned.
9
Pull the controller up to check if it is locked
10
Extra barcode labels are supplied with the controller
Example list and map.
Inside pole door
www.schreder.com /4
3
DOC-0020638 OWLET IV NEMA-INS-B | 10-2022
SELF-TEST
11
Note : the self-test occurs only in the first 5 power cycles after installing the controller.
2
3
1
The controller reduces light to minimum level.
When powering on luminaire, the light switches ON to maximum level.
The controller switches OFF the light completely.
2
3
2
3
1
1
2
3
1
100%
10%
30 seconds
100%
10%
100%
10%
100%
10%
30 seconds
30 seconds
30 seconds
OPTIONAL SENSOR TEST trigger a sensor dectection in the luminaire
Correct Luminaire is ON
4 Built-in LED controller is ON Incorrect Luminaire is OFF
Correct: Light level changes from max to min 5
Incorrect: Light level does not change
5
5
4
4
5
4
100% 10%
120 minutes
100% 10%
100% 10%
100% 10%
120 minutes
120 minutes
120 minutes
120 minutes
6
After the self-test, the luminaire operates as configured on the CMS platform.
6
6
6
www.schreder.com /4
4
DOC-0020638 OWLET IV NEMA-INS-B | 10-2022
Page 1 Page 2 Page 3 Page 4 Page 5Powered by FlippingBook