Performance
Characteristics
GENERAL INFORMATION Recommended installation height
ELECTRICAL INFORMATION Electrical class
Power consumption (W)
Luminaire output flux (lm)
Nominal flux (lm) (*)
Nominal efficacy (lm/W)
Luminaire efficacy (lm/W)
2m to 4m
EU class I or II
Nominal voltage
230V +3%/-10% - 50Hz
FutureProof
Easy replacement of the photometric engine and electronic assembly on-site
Line Current (A)
Power factor
> 90% at full load
Luminaire
Typical
Typical
Typical
Typical
Typical
Electromagnetic compatibility (EMC)
SANS 55015:2013/A1:2015, SANS 61000-3-2:2014, SANS 61000-3- 3:2013, SANS 61547:2009, SANS 62493:2015
Driver included
Yes
0.03
1128
7
161
936
134
ROHS compliant
Yes
Testing standard
SANS 60598, SANS 62262
OPTICAL INFORMATION LED colour temperature 4000K (Neutral white 740) Colour rendering index (CRI) ≥ 70 (Neutral white 740)
0.06
2256
14
161
1872
134
HOUSING AND FINISH Housing
Marine grade high-pressure die-cast aluminium (EN 1706 AC-44300)
Diffuser
High-impact acrylic (*)
0.03
1128 / 356 (**)
7
161
936
134
OPERATING CONDITIONS Operating temperature range (Ta)
Housing finish
Black (RAL 9017), Textured finish
-20°C to +35°C
Tightness level
IP 65
Maintenance
Easily accessible
0.06
2256 / 712 (**)
14
161
1872
134
(*) Suitable for Food & Beverage industry
LIFETIME OF THE LEDS @ TQ 25°C For all versions
Tolerance on LED flu x is ± 7% and on total luminaire power ± 5% (*) The nominal flux is an indicative LED flux @ Ts 85°C based on LED manufacturer’s data. The real flux output of the luminaire depends on environmental conditions (e.g. temperature and pollution) and the optical efficiency of luminaire. The type of LED used is subject to change due to the ongoing rapid progress taking place in LED technology. (**) Reduced output during battery back-up mode. Battery back-up of 4 hours.
50,000h - L70B10
DIMENSIONS AND MOUNTING A (mm) B (mm) C (mm) D (mm) 195 341 101 48
LIFETIME OF THE DRIVER @ TQ 25°C For all versions
50,000h ≤10% failure rate
Weight (kg)
Up to 2.5
A
Construction Details The luminaire consists of a marine grade high-pressure die-cast aluminium (EN 1706 AC-44300) base and trim ring, and an opaque or clear prismatic high-impact acrylic diffuser. It is designed to operate LEDs from 1128lm (7W) to 2256lm (14W). The luminaire bears the SANS 60598-2-1 safety mark. IP 65 in compliance with SANS 60598-2-1: The IP rating is certified by an SABS test report. All base castings are finished both outside and inside in white epoxy powder coating for added protection and reflectivity. It is simple to install due to four mounting holes provided outside the optical compartment through lugs that form part of the base casting. The trim ring casting is finished in a special multi-stage epoxy powder surface coating, is mounted onto the base casting by stainless steel M5 Allen head screws, located outside the optical compartment. The fixing holes can be supplied with stainless steel helicoil inserts on request. An opaque or clear prismatic non-discolouring high-impact acrylic injection moulded diffuser is used throughout the range. It offers excellent vandal resistance, is highly translucent and will not discolour even when subjected to the harshest UV environments. A silicon sponge gasket is fitted into a special groove in the diffuser to prevent damage to the gasket during installation. It fits snugly over a tongue provided on the base casting, thus achieving the certified ingress protection rating of IP 65. The electronic control gear is mounted directly onto the base casting. All external screws, bolts and metals are stainless steel or of non-corrosive material. Mains connections are by means of a suitable screw terminal block with a wire clamping contact. The power factor is rated at ≥0,9.
2mm
370
371
Powered by FlippingBook