Schréder Australia Pty Ltd Bldg 4A, Parklands Estate, 21-23 South Street, Rydalmere, NSW 2116, Australia T: 1300 489 780 | ABN 17 604 331 937 www.sylvania-schreder.com
POLE MOUNTING BUILT-IN DRIVER Following are guidelines and typical pole layout drawings that may be used when mounting the BUILT-IN drivers in poles. As there are many variations in pole design, please consult supplier for further information if the recommended spacing between drivers or any other guidelines cannot be achieved. 1. When mounting BUILT-IN drivers in poles they must be mounted vertically with the terminations at the bottom. 2. The space between the black lid of a lower driver and the termination on the bottom of a driver mounted above is to be at least 200mm. 3. The space between adjacent drivers side by side should be a minimum of 25mm but ideally 50mm. 4. The driver is supplied with a universal bracket which can be positioned in two locations along the edge of the driver on the underside of the black section. The bracket can be oriented so that keyhole slots are visible above the black lid or the bracket can be turned 180° and then used to hook over the top edge of a panel or strap. When mounting in poles with a typical 900*380mm flat panel, the drivers that are to be hanging down below the bottom edge of the door will have the bracket oriented so that the keyhole slots protrude above the black lid and suitable self- threading screws can be used through the keyholes. Drivers that are to be mounted above the top of the door will have the mounting bracket oriented so that it is used to hook over the top edge of the panel and screws can then be used to rigidly fix to the panel. Typically when using the keyholes for lower drivers the brackets will be positioned on the upper most position on the tray and for driver intended to be hanging on the panel above the door, the bracket will be positioned on the lowest position. 5. Panels can be pre-drilled and fitted with self-threading screws prior to positioning the drivers in the pole. A typical panel drilling layout is shown below; however the installer should check the layout suitability based on the pole type used. 6. The two off M5 lift screws on either side of the black section can be used as aids to installation for attaching rope, chain, hooks for lifting. These lift points are not for permanent mounting. Never lift driver over personal or any part of the body. 7. Drivers that are lowered down below the door opening can have short lengths of cable (0.8-1.0m) pre-terminated so that they can be easily connected to a termination point in an accessible area near the centre of the door opening. 8. There are 4 off M5 screws in the lid of the driver that may be used to mount DIN rail. The DIN rail can be mounted horizontally on a single driver or it can straddle two drivers. If DIN rail is mounted vertically ensures that it does not protrude too far toward the black cover on a lower driver as the black area is the hottest part and low temperature components such as TPS/PVC cables should be at least 20mm away from it. Mounting plate drilling position for panel 380 x 900 Driver Position Code: Driver through Door 1 (D1), Driver on Bottom (B) & Driver on Top (T). ( Eg. First bottom driver through door 1: D1.B1)
Hook the driver D1.T1, D1.T2 & D3.T1 on mounting plate by using the Bracket Provided (Screw the mounting Bracket to the bottom holes as shown)
Lifting Point
D1.T1
D3.T1
D1.T2
Use the key holes to mount units D1.B1, D1.B2, D2.B1, D2.B2 & D3.B1 on mounting plate by using the Bracket Provided.
D2.B2
D2.B1
87.5
205
(Screw the mounting Bracket to the Top holes as shown)
900
Note : Not all 3 holes in each set are necessary as single large bolt can be used in tapped centre hole or only 2 smaller screws in outer holes.
844
D3.B1
D1.B1
D1.B2
466
380
PAGE 8 OF 13
Document Version 2025-04
Rev: 2.3
Powered by FlippingBook